Cisco Aironet 1810W Series Access Point + Bluetooth, 2xkom

Prodaje se CISCO air-ap1810w-b-k9 nikad korišteni

all info on:
https://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1810w-series-access-points/datasheet-c78-736869.html


Za dodatne info zvati na mob...


Specification

Authentication and security

● Advanced Encryption Standard (AES) for Wi-Fi Protected Access 2 (WPA2)
● 802.1X, RADIUS authentication, authorization and accounting (AAA)
● 802.11i

Software

● Cisco Unified Wireless Network Software with AireOS Wireless Controllers Release 8.2.111.0 or later

Maximum clients

● Maximum number of associated wireless clients: 200 per Wi-Fi radio, in total 400 clients per access point

802.11ac

● 2x2 single-user/multiuser MIMO with two spatial streams
● Maximal ratio combining (MRC)
● 20-, 40- and 80-MHz channels
● PHY data rates up to 866.7 Mbps (80 MHz on 5 GHz)
● Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Rx)
● 802.11 Dynamic Frequency Selection (DFS)
● Cyclic shift diversity (CSD) support

Ethernet ports

● Authentication with 802.1X or MAC filtered
● Dynamic VLAN or per port
● Traffic locally switched or tunneled back to wireless LAN controller

Bluetooth

● Integrated Bluetooth 4.1 (including BLE) radio
● Maximum transmit power: 5 dBm
● Antenna gain: 2 dBi




Compatible with 2x2 multi-user multiple input, multiple output technology, the Aironet 1810W Wireless Access Point from Cisco provides multiple data pathways allowing two devices to communicate with the AP at the same time with data transfer rates of up to 867 Mbps. In addition to MU-MIMO technology, this Cisco access point operates on both the 2.4 GHz and 5 GHz frequencies and supports 802.11b/g/n networking standards. If a wired connection is needed, the Aironet 1810W also comes equipped with three Gigabit Ethernet ports, a single Gigabit Ethernet uplink port, and one passive pass-through RJ-45 port. Once installed dedicated LED indicators depict the boot loader status, association status, operating status, boot loader warnings, and boot load errors to keep network admins aware of the operational state of the AP.

MU-MIMO
Multiuser (MU) multiple-input multiple-output (MU-MIMO) allows transmission of data to multiple 802.11ac Wave 2-capable clients simultaneously to improve the client experience. Prior to MU-MIMO, 802.11n and 802.11ac Wave 1 access points could transmit data to only one client at a time, typically referred to as single-user MIMO.

Dedicated 802.11ac Wave 2 with 2x2 MIMO technology supports two spatial streams when operating in single-user or multiuser MIMO mode, offering 867 Mbps rates for more capacity and reliability than competing access points.

Gigabit Ethernet Ports
Three local Gigabit Ethernet ports are available to securely connect wired devices to the network. Traffic from wired devices can be tunneled back to a wireless LAN controller (for compatible controllers) or be locally switched by the access point. One of these Ethernet ports can also provide Power over Ethernet (PoE) out to power a device such as an IP phone or a security camera.

Integrated Bluetooth 4.1
Integrated Bluetooth low-energy (BLE) 4.1 radio for location and asset tracking

Multiple Mounting and Security Options
Multiple mounting options to standard junction boxes. You can vertically mount the access point directly on a wall or desk using the optional sleek desk cradle. Physical security is offered with the included Torx screw and the option to add a Kensington lock. Place your access point where you see fit, secure in the knowledge that it isn't going anywhere.